logo
Huis
Producten
Ongeveer ons
Fabrieksreis
Kwaliteitscontrole
Contacteer ons
Vraag een offerte aan
Nieuws
TOGETHER HTL LTD
Thuis Nieuws

Conveyor Belt Joint Types for MDF, HDF, Particleboard and OSB Production Lines

TOGETHER HTL LTD is een zeer goed bedrijf, ik ben zeer bereid om met u samen te werken, veilig, efficiënt, professioneel, eerlijk, gelukkig! Bedankt voor het leveren van stabiele service en producten. -----EUROPAT

—— INDUSTRIËLE EUROPT

Ik ben online Chatten Nu
Bedrijf Nieuws
Conveyor Belt Joint Types for MDF, HDF, Particleboard and OSB Production Lines
Laatste bedrijfsnieuws over Conveyor Belt Joint Types for MDF, HDF, Particleboard and OSB Production Lines

Are you looking for a replacement conveyor belt but unsure which joint type to choose? Is a Z-splice better than a spiral ring, double pin ring or steel clip joint?

The joint is an important part of an industrial conveyor belt. It connects the belt ends and must withstand continuous tension, bending, friction and repeated passage over pulleys.

In wood-based panel production, different belts work in different environments. Forming belts carry loose fibers or particles, pre-press belts operate under compression and tension, deaeration belts need suitable air permeability, and steam mesh belts must allow steam to pass through.

For this reason, joint selection should be based on the application rather than one joint type being used for every belt.

1. Z-Splice Joint — For Forming and Pre-Press Belts

A Z-splice is produced by cutting the belt ends into an interlocking finger pattern and joining them to form a continuous belt.

Advantages:

  • Relatively smooth and flat joint profile

  • No raised steel fastener across the belt surface

  • Good running transition when correctly manufactured

  • Suitable for applications requiring a continuous contact surface

It is commonly selected for forming belts and pre-press belts, where stable conveying and a smooth belt surface are important.

For permeable belt constructions, the splice area should also be checked to ensure that the joint does not create an unacceptable restriction in the required airflow.

laatste bedrijfsnieuws over Conveyor Belt Joint Types for MDF, HDF, Particleboard and OSB Production Lines  0

laatste bedrijfsnieuws over Conveyor Belt Joint Types for MDF, HDF, Particleboard and OSB Production Lines  1

2. Spiral Ring Joint — For Selected Permeable and Transfer Belts

A spiral ring joint connects the two belt ends using spiral-shaped connecting elements. It is particularly relevant to compatible mesh and open-structure belts.

Advantages:

  • Suitable for selected woven mesh belt structures

  • Allows opening and reconnection when the installation design permits

  • Provides a practical connection for certain air- and steam-permeable belts

  • Can simplify installation where an endless belt is difficult to fit

Typical applications include:

  • Deaeration belts

  • Steam mesh belts

  • Intermediate belts

The spiral connector must be compatible with the belt thickness, mesh geometry, operating tension and pulley arrangement.

laatste bedrijfsnieuws over Conveyor Belt Joint Types for MDF, HDF, Particleboard and OSB Production Lines  2


3. Double Pin Ring Joint — For Serviceable Mesh Belt Connections

A double pin ring joint uses two pins passing through aligned loops at the belt ends.

Advantages:

  • Mechanical connection that can be opened for maintenance

  • Practical for installation in machines with limited access

  • Pins can be inspected and replaced where the design allows

  • Suitable for certain permeable mesh belts

It is an option for selected deaeration belts and steam mesh belts. The pin diameter, material, loop construction and joint strength should be confirmed according to the actual operating load.

laatste bedrijfsnieuws over Conveyor Belt Joint Types for MDF, HDF, Particleboard and OSB Production Lines  3

4. Endless Joint — Continuous Belt Without a Separate Mechanical Fastener

An endless belt is supplied as a closed loop rather than being connected by a separate mechanical joint at the installation site.

Advantages:

  • Continuous running surface

  • No exposed metal fastener

  • No separate pin or spiral connector

  • Can be useful where surface continuity is important

An endless construction may be considered for certain deaeration belt applications. However, the machine must provide sufficient access for installation and replacement, and the belt must be manufactured to the required circumference.

5. Steel Clip Joint — Convenient for On-Site Installation

A steel clip joint uses metal fasteners to connect the belt ends.

Advantages:

  • Fast installation

  • Convenient for field replacement

  • Practical for certain maintenance and repair situations

  • Does not require the same type of bonded splice process as a Z-splice

It is a suitable option for many bin bottom or storage belt applications, where convenient maintenance is often a priority.

However, steel clips create a raised mechanical connection. On belts that contact a fragile mat or require a smooth surface, the potential for joint marks, roller impact and localized wear should be considered.

laatste bedrijfsnieuws over Conveyor Belt Joint Types for MDF, HDF, Particleboard and OSB Production Lines  4

6. Recommended Joint Options by Belt Application

Belt type Commonly considered joint
Forming belt Z-splice
Pre-press belt Z-splice
Deaeration belt Z-splice, spiral ring, double pin ring, endless or steel clip, depending on design
Intermediate belt Spiral ring
Steam mesh belt Spiral ring or double pin ring
Bin bottom belt Steel clip

The table is a selection reference, not a fixed specification for every production line. The final design must be confirmed against the belt structure and machine requirements.

7. What Information Is Needed to Select the Right Joint?

When requesting a quotation for a replacement belt, please provide:

  1. Belt application and machine section

  2. Belt width, length or circumference, and thickness

  3. Existing joint type and close-up photos

  4. Pulley diameters and operating speed

  5. Working tension and installation arrangement

  6. Whether air or steam must pass through the belt

  7. Whether the belt can be installed as a closed loop or must be joined on site

For further product information:


Pre-press Belt without Perforated

Pre-press Belt with Perforated

Deaeration Belt with Carbon Fiber

Deaeration Belt with Copper Wire

Customized Belt and Joint Selection

There is no single joint that is best for every application. A smooth Z-splice may be suitable for one belt, while a spiral or pin connection may be more practical for another. A steel clip can be convenient for maintenance, while an endless belt can eliminate a separate mechanical fastener.

The best choice balances joint strength, surface requirements, permeability, installation access and operating conditions.

Need a replacement belt but are unsure about the joint?

Send us the belt dimensions, machine details and photos of the existing connection. We can review the application and recommend a suitable joint construction for confirmation.

Bartijd : 2026-11-15 17:42:01 >> Nieuwslijst
Contactgegevens
TOGETHER HTL LTD

Contactpersoon: Mr. Maple

Tel.: +86 17778255675

Fax: 86--311-80690567

Direct Stuur uw aanvraag naar ons (0 / 3000)