Film slippage is a common problem in plastic film production and continuous web-handling applications. It can cause unstable film movement, wrinkles, tension fluctuations, poor winding quality, and production interruptions.
One important factor affecting traction is the hardness of the rubber roller covering.
Rubber hardness influences how the roller deforms under pressure and how its surface contacts the film. A suitable hardness can help maintain stable contact conditions, while an unsuitable specification may contribute to slippage or other mechanical problems.
However, softer rubber does not automatically provide better traction. The correct hardness depends on film material, film thickness, roller diameter, nip pressure, production speed, rubber compound, and operating temperature.
Rubber rollers are widely used in plastic film production lines for pulling, feeding, guiding, pressing, and conveying film.
When a rubber roller contacts the film, the covering deforms under the applied load. This deformation influences the contact area and pressure distribution between the roller and film.
Under comparable conditions, softer rubber generally deforms more than harder rubber. This may allow the roller surface to conform more closely to the film and help distribute pressure.
However, actual traction also depends on the friction characteristics of the rubber and film surfaces.
A suitable roller specification should therefore consider both contact behavior and the mechanical properties of the rubber compound.
If the rubber covering is too hard for the application, it may not deform sufficiently under the available nip load.
Possible problems include:
Insufficient conformity to the film surface
Limited contact under certain loading conditions
Uneven contact across the roller width
Greater sensitivity to roller alignment
Insufficient traction under some operating conditions
If film slippage occurs despite apparently correct nip pressure, the rubber hardness and surface condition should be checked.
However, other causes such as worn rubber, contamination, incorrect alignment, and unstable web tension should also be investigated.
A very soft rubber covering can deform more easily, but excessive deformation may create additional problems.
These may include:
Excessive compression under nip pressure
Increased rolling resistance
Heat buildup during continuous operation
Faster wear under unsuitable conditions
Changes in effective roller diameter
Reduced dimensional stability
These issues can become more important at higher production speeds.
The objective is to select a hardness that provides sufficient contact conformity without sacrificing the mechanical stability required by the production line.
Rubber hardness is commonly measured using the Shore A scale.
A lower Shore A value indicates softer rubber, while a higher value indicates harder rubber.
For film-handling rollers, Shore A hardness influences the amount of deformation under applied pressure.
However, hardness does not directly determine the coefficient of friction between rubber and film.
Two rubber compounds with the same Shore A hardness may have different friction characteristics, elasticity, abrasion resistance, and heat resistance.
Therefore, hardness should be evaluated together with:
Rubber compound formulation
Elasticity and resilience
Friction characteristics
Abrasion resistance
Covering thickness
Roller diameter
Nip pressure
Operating temperature
Production speed
There is no universal Shore A value suitable for every plastic film production line.
Different polymer films have different surface and mechanical characteristics.
Common materials include:
BOPP film
BOPET film
PE film
CPP film
Other specialty polymer films
The same rubber roller specification may not provide identical traction performance with every film material.
Film thickness is also important. Thin films may be more sensitive to local pressure, stretching, marking, and deformation.
For this reason, rubber hardness and nip pressure should be evaluated together rather than independently.
A pulling roller used for thin BOPET film may require a different specification from a roller handling thicker PE film.
The actual selection should follow the film characteristics and the function of the roller position.
Rubber compound selection is another important part of traction control.
Common covering materials include:
NBR rubber: Often considered for applications involving oils and selected industrial fluids.
EPDM rubber: Commonly considered for water, steam, and certain chemical environments.
Polyurethane: Often selected where abrasion resistance and mechanical strength are important.
Silicone rubber: May be considered for applications requiring particular temperature characteristics.
These are general material tendencies. Actual compatibility and performance depend on the compound formulation and operating conditions.
Surface finish also influences contact behavior. Depending on the film and roller function, a ground or textured rubber surface may be considered.
Hardness, compound formulation, and surface finish should be treated as parts of one roller specification.
When film slippage occurs, changing rubber hardness should not be the only adjustment.
A systematic inspection should include:
Measure the actual rubber hardness and compare it with the specified value.
Inspect the roller surface for wear, contamination, glazing, or damage.
Check nip pressure and pressure distribution across the working width.
Verify roller parallelism and alignment.
Check web tension and line speed stability.
Confirm that the rubber compound is suitable for the film and operating environment.
Inspect bearings, drive components, and synchronization.
It is also important to understand when slippage occurs.
Does it happen during acceleration? Does it appear only at higher speeds? Does it occur during winding? Is it limited to one side of the film?
These details help determine whether the issue is related to traction, tension control, drive synchronization, or roller condition.
When requesting a new or replacement rubber roller, prepare the following information:
Machine manufacturer and model
Roller position and working function
Roller diameter and face length
Overall length and shaft dimensions
Core material
Rubber compound, if known
Required Shore A hardness
Rubber covering thickness
Film material and thickness
Operating speed
Nip pressure or loading method
Operating temperature
Existing roller drawing or sample
If the existing roller is causing film slippage, describe the problem and the operating conditions when it occurs.
This information helps evaluate whether the specification needs to change in terms of hardness, compound, surface finish, or another mechanical parameter.
HUATAO Group focuses on industrial products and works closely with qualified manufacturers to coordinate customized roller supply for plastic film, paper, printing, and converting industries.
Our product scope includes Rubber Rollers, Cooling Rolls, and other industrial roller solutions.
For film-handling applications, rubber hardness, compound formulation, covering thickness, surface finish, and roller dimensions should be evaluated together.
A pulling roller, guide roller, and pressure roller may require different specifications even when they are installed on the same production line.
For more information, explore:
About HUATAO
Other Industrial Rolls
Polyfilm Line Rolls
Industrial Roller Covers
Whether you need a replacement rubber roller or a customized roller for a new film production line, providing the original drawing and application details is the best starting point.
Contact
Tony Liu
General Manager | International Department
HUATAO Group
Mobile / WhatsApp / WeChat: +86 13383112591
Email: sale08@huataogroup.com
Website: https://www.huataorolls.com/
Contactpersoon: Mr. Maple
Tel.: +86 17778255675
Fax: 86--311-80690567